Departments
Solutions
PRO
Browsing History
Main Menu
Batteries
Biomedical
Cables & Sensors
Computers & Electronics
Facilities & Workspaces
Laboratory
Lighting & Bulbs
Medical Imaging
Minor Equipment
On-Site Service
Repair
Training
Shop by OEM
Shop by Model
Main Menu
Provider
Supplier
Government
Partners
GPOs
Resources
About
Main Menu
About PartsSource PRO
On-Demand Parts
On-Demand Service
Repair & Service Agreements
Main Menu
My Account
Orders
Quotes
Depot Repairs
On-Site Service
Exchanges & Returns
Settings
Main Menu
Month over Month Spend
Prior Rebates
Main Menu
My Lists
Create New List
OEM#: 6600-0071-800New OEM Original Outright
KIT PROBE COMPT CARE PLUS INCUBATOR ASSEMBLY by Datex-Ohmeda
Your price:
$593.02 each $600.00 Savings: $6.98 (1%)
Estimated to ship by 04/20 if ordered before 4:00 PM EST
OEM#: 6600-0071-800KIT PROBE COMPT CARE PLUS INCUBATOR ASSEMBLY by Datex-Ohmeda
New OEM Original Outright
Your price:
$593.02 each
$600.00 Savings: $6.98 (1%)
Estimated to ship by 04/20 if ordered before 4:00 PM EST
Asset Information
Drop Shipped From GE - Not For Export Out Of US
ADD TO LIST
Product Overview
The Kit Probe is used in the compartment air probe assembly of an incubator. The kit consists of a sensor assembly, shim sensor, screw, cable clamp and nut. The control board contains 16 channel multiplexer. There are seven temperature measurement channels. These channels measure the two patient probes with two thermistors each, the two air temperature thermistors used for display and control, and an additional thermistor used to measure the heat sink temperature. Using a 2.5mm hex key, remove the screw that secures the jack cable clip to the hood back wall. Remove the 2 screws (2mm hex key) that secure the probe housing cover and remove it. The top screw secures the probe shield, so that it can now be removed from the inside front of the probe housing. Disconnect the electrical connectors for the temperature and humidity sensor (if installed) wires and remove the front of the probe housing. To replace the temperature sensor, you must replace the entire probe housing.
Features
- Manufacturer: Datex-Ohmeda
- Condition: New OEM Original
- Purchase Type: Outright
- Warranty: 90 Day
- Returnable: No
- Easy to install
- Easy to remove
Equivalents
- 6600-0071-800: GE Healthcare
Fitments
- Datex-Ohmeda
- CARE PLUS
Technical Specs
P/N: 6600-0071-800 Key Specs
Item
KIT PROBE COMPT CARE PLUS INCUBATOR ASSEMBLY
OEM
Datex-Ohmeda
OEM #
6600-0071-800
Condition
New OEM Original
Returnable
No
The Kit Probe is used in the compartment air probe assembly of an incubator. The kit consists of a sensor assembly, shim sensor, screw, cable clamp and nut. The control board contains 16 channel multiplexer. There are seven temperature measurement channels. These channels measure the two patient probes with two thermistors each, the two air temperature thermistors used for display and control, and an additional thermistor used to measure the heat sink temperature. Using a 2.5mm hex key, remove the screw that secures the jack cable clip to the hood back wall. Remove the 2 screws (2mm hex key) that secure the probe housing cover and remove it. The top screw secures the probe shield, so that it can now be removed from the inside front of the probe housing. Disconnect the electrical connectors for the temperature and humidity sensor (if installed) wires and remove the front of the probe housing. To replace the temperature sensor, you must replace the entire probe housing.
- 6600-0071-800: GE Healthcare
- Datex-Ohmeda
- CARE PLUS
Product Overview
The Kit Probe is used in the compartment air probe assembly of an incubator. The kit consists of a sensor assembly, shim sensor, screw, cable clamp and nut. The control board contains 16 channel multiplexer. There are seven temperature measurement channels. These channels measure the two patient probes with two thermistors each, the two air temperature thermistors used for display and control, and an additional thermistor used to measure the heat sink temperature. Using a 2.5mm hex key, remove the screw that secures the jack cable clip to the hood back wall. Remove the 2 screws (2mm hex key) that secure the probe housing cover and remove it. The top screw secures the probe shield, so that it can now be removed from the inside front of the probe housing. Disconnect the electrical connectors for the temperature and humidity sensor (if installed) wires and remove the front of the probe housing. To replace the temperature sensor, you must replace the entire probe housing.
Features
- Manufacturer: Datex-Ohmeda
- Condition: New OEM Original
- Purchase Type: Outright
- Warranty: 90 Day
- Returnable: No
- Easy to install
- Easy to remove
Equivalents
- 6600-0071-800: GE Healthcare
Fitments
- Datex-Ohmeda
- CARE PLUS
Technical Specs
P/N: 6600-0071-800 Key Specs
Item
KIT PROBE COMPT CARE PLUS INCUBATOR ASSEMBLY
OEM
Datex-Ohmeda
OEM #
6600-0071-800
Condition
New OEM Original
Returnable
No
The Kit Probe is used in the compartment air probe assembly of an incubator. The kit consists of a sensor assembly, shim sensor, screw, cable clamp and nut. The control board contains 16 channel multiplexer. There are seven temperature measurement channels. These channels measure the two patient probes with two thermistors each, the two air temperature thermistors used for display and control, and an additional thermistor used to measure the heat sink temperature. Using a 2.5mm hex key, remove the screw that secures the jack cable clip to the hood back wall. Remove the 2 screws (2mm hex key) that secure the probe housing cover and remove it. The top screw secures the probe shield, so that it can now be removed from the inside front of the probe housing. Disconnect the electrical connectors for the temperature and humidity sensor (if installed) wires and remove the front of the probe housing. To replace the temperature sensor, you must replace the entire probe housing.
- 6600-0071-800: GE Healthcare
- Datex-Ohmeda
- CARE PLUS
Product Overview
The Kit Probe is used in the compartment air probe assembly of an incubator. The kit consists of a sensor assembly, shim sensor, screw, cable clamp and nut. The control board contains 16 channel multiplexer. There are seven temperature measurement channels. These channels measure the two patient probes with two thermistors each, the two air temperature thermistors used for display and control, and an additional thermistor used to measure the heat sink temperature. Using a 2.5mm hex key, remove the screw that secures the jack cable clip to the hood back wall. Remove the 2 screws (2mm hex key) that secure the probe housing cover and remove it. The top screw secures the probe shield, so that it can now be removed from the inside front of the probe housing. Disconnect the electrical connectors for the temperature and humidity sensor (if installed) wires and remove the front of the probe housing. To replace the temperature sensor, you must replace the entire probe housing.
Features
- Manufacturer: Datex-Ohmeda
- Condition: New OEM Original
- Purchase Type: Outright
- Warranty: 90 Day
- Returnable: No
- Easy to install
- Easy to remove
How can we
improve our item listing
?Equivalents
- 6600-0071-800: GE Healthcare
Fitments
- Datex-Ohmeda
- CARE PLUS
Technical Specs
P/N: 6600-0071-800 Key Specs
Item
KIT PROBE COMPT CARE PLUS INCUBATOR ASSEMBLY
OEM
Datex-Ohmeda
OEM #
6600-0071-800
Condition
New OEM Original
Returnable
No
The Kit Probe is used in the compartment air probe assembly of an incubator. The kit consists of a sensor assembly, shim sensor, screw, cable clamp and nut. The control board contains 16 channel multiplexer. There are seven temperature measurement channels. These channels measure the two patient probes with two thermistors each, the two air temperature thermistors used for display and control, and an additional thermistor used to measure the heat sink temperature. Using a 2.5mm hex key, remove the screw that secures the jack cable clip to the hood back wall. Remove the 2 screws (2mm hex key) that secure the probe housing cover and remove it. The top screw secures the probe shield, so that it can now be removed from the inside front of the probe housing. Disconnect the electrical connectors for the temperature and humidity sensor (if installed) wires and remove the front of the probe housing. To replace the temperature sensor, you must replace the entire probe housing.
- 6600-0071-800: GE Healthcare
- Datex-Ohmeda
- CARE PLUS